The 'standard plots' for EG078D are as follows:

  eg078e-weight.ps                    station weight vs. time 
  eg078e-auto-[1-3].ps                station autocorrelation vs. freq
  eg078e-cross-[1-3][a,p].ps          baseline amp/phs vs. freq
  eg078e-ampphase-[a1,p[1-4].ps       Ef-* & O8-* baseline amp/phs vs. time

The auto and cross plots show 1 minute of data from scans 142 (3C345, [1]) 
and 172 (DA193, [2]), and all of scan 23 (J1241+602, [3]).  Among these,
[1] misses Ur,Tr,T6,Bd; [2] misses Tr; and [3] misses Jb.
The ampphase plots show amp [a] and phase [p] versus time, in a few
variants as described below.

The antenna numbering in these plots is 0-based -- thus one less than the
corresponding antenna numbers in the AIPS FITS file.


(a) WEIGHT plots

  The plots shows the weights for all IFs/pols per station, with each
3s integration plotted as a separate ".".   The IF/pol color-coding is:

 IF1/RR = red    IF1/LL = blue      IF2/RR = cyan        IF2/LL = green
 IF3/RR = pink   IF3/LL = med.grey  IF4/RR = brown       IF4/LL = purple
 IF5/RR = teal   IF5/LL = yellow    IF6/RR = steel blue  IF6/LL = lt.grey
 IF7/RR = black  IF7/LL = orange    IF8/RR = lt.green    IF8/LL = lt.purple


(b) AUTOCORRELATION SPECTRA plots

  The plots show data from the scans listed above.  Each IF is plotted in
a separately-scaled panel for each row (station), in order to isolate the
effects of RFI on individual IF(s).  Since each plot self-scales, y-axes
may not go down to zero.  The polarization color-coding is RR=red, LL=blue. 


(c) BASELINE SPECTRA plots 

  The baseline vs. frequency plots show vector-averaged amplitude and phase 
for all baselines for same the time ranges as the autocorrelation plots, with
with amp & phase going to separate plots denoted by the 'a' or 'p' following
the scan identifier, using the same baseline lay-out on the page for each scan.
IFs per baseline are separated by the dashed vertical lines.  The polarization 
color-coding is RR=red, LL=blue.


(d) AMP/PHASE(t) plots 

  The baseline vs. time plots show amplitude and phase for non-target scans,
with amp & phase going to separate plots, denoted by the 'a' or 'p' following
'ampphase-'.  Each 3s integration is plotted as a separate ".", with the
middle 80% of the band used for vector-averaging over frequency.  T6 serves
as the reference station and the IF/pol color-coding is the same as in the 
weight plot, unles otherwide indicated.  Baselines to both Ef and O8 are
shown because Ef has only LCP good.

There's one amp(t) plot:
  a1 - J1234+619 & J1241+602 for the whole experiment (omits the fringe
         finders to avoid their dominating the y-axis scale)  

There are four phase(t) plots:
  p1 - all non-target scans for the whole experiment
  p2 - the same, but with integration number within each baseline along 
          the x-axis rather than time ("collapses" the gaps between these
          scans in order to make the phase traces easier to follow, 
          at the expense of a discontinuous abscissa).
  p3 - the same as [p2], but with only LCP (for the benefit of Ef & Ro)
  p4 - the same as [p2], but without J1234+619 scans.

The color coding for [p3] is
 IF1/LL = red    IF2/LL = blue      IF3/LL = cyan        IF4/LL = green
 IF5/LL = pink   IF6/LL = med.grey  IF7/LL = brown       IF8/LL = purple