EVN User Experiment Pipeline Feedback


Pipeline feedback for experiment EK046A. If you have any comments on this experiment please email the address below.
A detailed description of the pipeline output is available.


Last updated: za mrt 28 21:45:52 CET 2020 bayandina@jive.eu


General Comments. ( Brief data summary and scan listing )
EK046A. K-band experiment observed on 17 October 2019. This is a continuum pass dataset.
The data rate was 2048 Mbps (8 x 32 MHz subbands, full polarization, two-bit sampling)

The target sources J0153+7115, J0824+5552, J0854+5757, J1010+8250, J1126+4516, J1148+5254, J1217+5835, J1234+4753, J1335+4542, J1436+6336, J1624+5741, J1638+5720, J1658+4737, J1927+7358, J2031+5455, J0741+3112, J0745+3142, J0815+3635, J0839+1802, J0842+1835, J0940+2603, J1023+3948, J1159+2914, J1331+3030, and J1407+2827 were directly fringe-fitted.
J1638+5720 and J1927+7358 were also observed as calibrators and fringe finders.

17 stations participated: Jb, Ef, Mc, O6, T6, Ur, Tr, Ys, Hh, Sv, Zc, Bd, Sr, Mh, Ky, Ku, Kt.

The following are plots from the EVN pipeline analysis, in which the reference antenna was: Ef.


Plots of the autocorrelations
Comments.
Auto-corr amplitude vs frequency plots for each station showing all IFs and Pols.


Plots of the uncalibrated amplitude and phase against time
Comments.
Amplitude and phase vs time, for the whole experiment, no calibration applied. Shows visibilities on all baselines to the reference antenna. All IFs and Pols shown. This is a good place to look for stations that missed scans during the experiment.


Plots of the uncalibrated amplitude and phase against frequency channel
Comments.
Uncalibrated, vector averaged, cross power specra for baselines to the reference antenna. No bandpass calibration applied yet. This is a good place to check how well detected sources are on each baseline.


The uncalibrated amplitude and phase of the crosshand correlations against frequency channel
Comments.


TSYS against time
Comments.
Plots of system temperature vs time for each station (and each IF). Flat-line plots indicate that this information was not available for a given station, in which case we create a generic Tsys table scaled to the station's gain (Jy/K). This information is stored in the TY1 table.


Telescope sensitivities from the a priori TSYS and Gain curves (the square of this number gives the antenna noise (SEFD) in Jy - the smaller the better).
Comments.
Gain info in CL2, determined using Tsys tables. Plot shows Gain vs time for each station, each IF and each Pol.


Fringe-fit phase solutions (including Parallactic Angle correction).
Comments.
Plot of CL3. This is the CL table generated using CL2 (amplitude cal) and SN2 (FRING solutions). Plot shows phase calibration data vs time. Missing data indicate possible issues in those previous steps. If no issues arose, then use this table to phase-reference the target.


Fringe-fit delay solutions
Comments.
Plot of SN2. Shows delay vs time from FRING results (usually only calibrators and reference sources). This is a good place to look for times where FRING failed to get solutions. Here, FRING uses a signal to noise cutoff of 5.


Fringe-fit rate solutions
Comments.
SN2 as above, but for rate.


Telescope bandpasses
Comments.
Plot of BP1. Shows the bandpass characteristics of each antenna, determined using the brightest source(s) in the experiment. Look for small dispersion in the phase data, this indicates a high signal to noise ratio - and thus a good bandpass characterisation.


Calibrated amplitude and phase against time (a priori amplitude calibration and fringe-fit solutions applied).
Comments.
Plot of visibilities vs time for all baselines to the reference antenna, after applying CL3. This is a good place to check the success of the amplitude calibration (CL2) and FRING (CL3) stages of the pipeline.


Calibrated amplitude and phase against frequency channel
Comments.
Amplitude and phase vs frequency plots for all baselines to the reference antenna, after applying CL3 and BP1. If the corrections of CL2, CL3 and BP1 are good enough, you will get flat phase and amplitude profiles, therefore this is a good place to check the success of CL2, CL3 and particularly BP1 for each scan/baseline/IF/Pol.


Naturally weighted dirty map (not useful for bright sources) produced before self-cal of:
J1023+3948: pdf (not available) , or FITS (not available) .
J1159+2914: pdf (not available) , or FITS (not available) .
J1331+3030: pdf (not available) , or FITS (not available) .
J1638+5720: pdf (not available) , or FITS (not available) .
J2031+5455: pdf (not available) , or FITS (not available) .
J1658+4737: pdf (not available) , or FITS (not available) .
J0854+5757: pdf (not available) , or FITS (not available) .
J1335+4542: pdf (not available) , or FITS (not available) .
J1217+5835: pdf (not available) , or FITS (not available) .
J0839+1802: pdf (not available) , or FITS (not available) .
J1234+4753: pdf (not available) , or FITS (not available) .
J1624+5741: pdf (not available) , or FITS (not available) .
J0741+3112: pdf (not available) , or FITS (not available) .
J0940+2603: pdf (not available) , or FITS (not available) .
J0842+1835: pdf (not available) , or FITS (not available) .
J0815+3635: pdf (not available) , or FITS (not available) .
J1126+4516: pdf (not available) , or FITS (not available) .
J1927+7358: pdf (not available) , or FITS (not available) .
J0745+3142: pdf (not available) , or FITS (not available) .
J1407+2827: pdf (not available) , or FITS (not available) .
J1010+8250: pdf (not available) , or FITS (not available) .
J1436+6336: pdf (not available) , or FITS (not available) .
J0824+5552: pdf (not available) , or FITS (not available) .
J1148+5254: pdf (not available) , or FITS (not available) .
J0153+7115: pdf (not available) , or FITS (not available) .
Comments.
Only phase-referenced targets are shown.


Uniformly weighted dirty map (not useful for bright sources) produced before self-cal of:
J1023+3948: pdf (not available) , or FITS (not available) .
J1159+2914: pdf (not available) , or FITS (not available) .
J1331+3030: pdf (not available) , or FITS (not available) .
J1638+5720: pdf (not available) , or FITS (not available) .
J2031+5455: pdf (not available) , or FITS (not available) .
J1658+4737: pdf (not available) , or FITS (not available) .
J0854+5757: pdf (not available) , or FITS (not available) .
J1335+4542: pdf (not available) , or FITS (not available) .
J1217+5835: pdf (not available) , or FITS (not available) .
J0839+1802: pdf (not available) , or FITS (not available) .
J1234+4753: pdf (not available) , or FITS (not available) .
J1624+5741: pdf (not available) , or FITS (not available) .
J0741+3112: pdf (not available) , or FITS (not available) .
J0940+2603: pdf (not available) , or FITS (not available) .
J0842+1835: pdf (not available) , or FITS (not available) .
J0815+3635: pdf (not available) , or FITS (not available) .
J1126+4516: pdf (not available) , or FITS (not available) .
J1927+7358: pdf (not available) , or FITS (not available) .
J0745+3142: pdf (not available) , or FITS (not available) .
J1407+2827: pdf (not available) , or FITS (not available) .
J1010+8250: pdf (not available) , or FITS (not available) .
J1436+6336: pdf (not available) , or FITS (not available) .
J0824+5552: pdf (not available) , or FITS (not available) .
J1148+5254: pdf (not available) , or FITS (not available) .
J0153+7115: pdf (not available) , or FITS (not available) .
Comments.
Only phase-referenced targets are shown.


Phase corrections applied to a priori calibrated and fringe-fitted data by self-calibration.
J1023+3948 .
J1159+2914 .
J1331+3030 .
J1638+5720 .
J2031+5455 .
J1658+4737 .
J0854+5757 .
J1335+4542 .
J1217+5835 .
J0839+1802 .
J1234+4753 .
J1624+5741 .
J0741+3112 .
J0940+2603 .
J0842+1835 .
J0815+3635 .
J1126+4516 .
J1927+7358 .
J0745+3142 .
J1407+2827 .
J1010+8250 .
J1436+6336 .
J0824+5552 .
J1148+5254 .
J0153+7115 .
Comments.
Individual plots for each source that was used in FRING. Shows phase selfcal solutions (SN1 after SPLIT). This is particularly useful to check if the reference source could be self-calibrated, and to look for missing scans/antennas.


Amplitude corrections applied to a priori calibrated and fringe-fitted data by self-calibration.
J1023+3948: pdf , or text file , or statistical summary .
J1159+2914: pdf , or text file , or statistical summary .
J1331+3030: pdf , or text file , or statistical summary .
J1638+5720: pdf , or text file , or statistical summary .
J2031+5455: pdf , or text file , or statistical summary .
J1658+4737: pdf , or text file , or statistical summary .
J0854+5757: pdf , or text file , or statistical summary .
J1335+4542: pdf , or text file , or statistical summary .
J1217+5835: pdf , or text file , or statistical summary .
J0839+1802: pdf , or text file , or statistical summary .
J1234+4753: pdf , or text file , or statistical summary .
J1624+5741: pdf , or text file , or statistical summary .
J0741+3112: pdf , or text file , or statistical summary .
J0940+2603: pdf , or text file , or statistical summary .
J0842+1835: pdf , or text file , or statistical summary .
J0815+3635: pdf , or text file , or statistical summary .
J1126+4516: pdf , or text file , or statistical summary .
J1927+7358: pdf , or text file , or statistical summary .
J0745+3142: pdf , or text file , or statistical summary .
J1407+2827: pdf , or text file , or statistical summary .
J1010+8250: pdf , or text file , or statistical summary .
J1436+6336: pdf , or text file , or statistical summary .
J0824+5552: pdf , or text file , or statistical summary .
J1148+5254: pdf , or text file , or statistical summary .
J0153+7115: pdf , or text file , or statistical summary .
Comments.
Individual plots for each source that was used in FRING. Shows amplitude selfcal solutions (SN2). This table is important to properly calibrate amplitudes from stations that had to use generic Tsys tables (see TSYS, above). In the statistical summary, values close to one mean a good a-priori calibration.


Telescope sensitivities (the total AMP gain applied during both a priori and self calibration; the square of this number gives the antenna noise (SEFD) in Jy).
Comments.
Plot of CL4 which shows amplitude calibrations determined from CL3 and the amplitude selfcal solutions from SN2 (from CALIB_AMP2, above). Comparison with GAIN plot (above) reveals the accuracy of the apriori amplitude calibration derived from the TSYS tables - this is particularly important for stations that have generic generated TSYS tables; Tsys may benefit from additional scaling if there is a large difference in SENS and GAIN plots.


Residual closure phase (visibility closure phase with model closure phase subtracted) for:
J1023+3948 .
J1159+2914 .
J1331+3030 .
J1638+5720 .
J2031+5455 .
J1658+4737 .
J0854+5757 .
J1335+4542 .
J1217+5835 .
J0839+1802 .
J1234+4753 .
J1624+5741 .
J0741+3112 .
J0940+2603 .
J0842+1835 .
J0815+3635 .
J1126+4516 .
J1927+7358 .
J0745+3142 .
J1407+2827 .
J1010+8250 .
J1436+6336 .
J0824+5552 .
J1148+5254 .
J0153+7115 .
Comments.
Closure phases for all triangles of antennas in the array. Individual plots for each source that was used in FRING.


Calibrated visibilities and the source model of:
J1023+3948 .
J1159+2914 .
J1331+3030 .
J1638+5720 .
J2031+5455 .
J1658+4737 .
J0854+5757 .
J1335+4542 .
J1217+5835 .
J0839+1802 .
J1234+4753 .
J1624+5741 .
J0741+3112 .
J0940+2603 .
J0842+1835 .
J0815+3635 .
J1126+4516 .
J1927+7358 .
J0745+3142 .
J1407+2827 .
J1010+8250 .
J1436+6336 .
J0824+5552 .
J1148+5254 .
J0153+7115 .
Comments.
Similar to VPLOT_CAL for sources used in FRING, however, each source has been individually SPLITed and modelled.


Calibrated visibilities against u,v distance for:
J1023+3948: pdf , or png .
J1159+2914: pdf , or png .
J1331+3030: pdf , or png .
J1638+5720: pdf , or png .
J2031+5455: pdf , or png .
J1658+4737: pdf , or png .
J0854+5757: pdf , or png .
J1335+4542: pdf , or png .
J1217+5835: pdf , or png .
J0839+1802: pdf , or png .
J1234+4753: pdf , or png .
J1624+5741: pdf , or png .
J0741+3112: pdf , or png .
J0940+2603: pdf , or png .
J0842+1835: pdf , or png .
J0815+3635: pdf , or png .
J1126+4516: pdf , or png .
J1927+7358: pdf , or png .
J0745+3142: pdf , or png .
J1407+2827: pdf , or png .
J1010+8250: pdf , or png .
J1436+6336: pdf , or png .
J0824+5552: pdf , or png .
J1148+5254: pdf , or png .
J0153+7115: pdf , or png .
Comments.
Plot of amplitude vs baseline length for each source. This can be useful to look for indications of structure at different angular scales.


u,v coverage for:
J1023+3948: pdf , or png .
J1159+2914: pdf , or png .
J1331+3030: pdf , or png .
J1638+5720: pdf , or png .
J2031+5455: pdf , or png .
J1658+4737: pdf , or png .
J0854+5757: pdf , or png .
J1335+4542: pdf , or png .
J1217+5835: pdf , or png .
J0839+1802: pdf , or png .
J1234+4753: pdf , or png .
J1624+5741: pdf , or png .
J0741+3112: pdf , or png .
J0940+2603: pdf , or png .
J0842+1835: pdf , or png .
J0815+3635: pdf , or png .
J1126+4516: pdf , or png .
J1927+7358: pdf , or png .
J0745+3142: pdf , or png .
J1407+2827: pdf , or png .
J1010+8250: pdf , or png .
J1436+6336: pdf , or png .
J0824+5552: pdf , or png .
J1148+5254: pdf , or png .
J0153+7115: pdf , or png .
Comments.
Plot of the UV coverage for each source during the experiment.


Crude maps of sources:
J1023+3948: pdf , or FITS .
J1159+2914: pdf , or FITS .
J1331+3030: pdf , or FITS .
J1638+5720: pdf , or FITS .
J2031+5455: pdf , or FITS .
J1658+4737: pdf , or FITS .
J0854+5757: pdf , or FITS .
J1335+4542: pdf , or FITS .
J1217+5835: pdf , or FITS .
J0839+1802: pdf , or FITS .
J1234+4753: pdf , or FITS .
J1624+5741: pdf , or FITS .
J0741+3112: pdf , or FITS .
J0940+2603: pdf , or FITS .
J0842+1835: pdf , or FITS .
J0815+3635: pdf , or FITS .
J1126+4516: pdf , or FITS .
J1927+7358: pdf , or FITS .
J0745+3142: pdf , or FITS .
J1407+2827: pdf , or FITS .
J1010+8250: pdf , or FITS .
J1436+6336: pdf , or FITS .
J0824+5552: pdf , or FITS .
J1148+5254: pdf , or FITS .
J0153+7115: pdf , or FITS .
Comments.
CLEANed image of each source (FRINGed or phase-referenced) after applying all relevant calibrations up to CL4 by the pipeline; including amplitude and phase self calibrations.