The 'standard plots' for EP088A are as follows:

  ep088a-weight-[1,2].ps          station weight vs. time 
  ep088a-auto-[1,2].ps            station autocorrelation vs. freq
  ep088a-cross-[1,2][a,p].ps      baseline amp/phs vs. freq
  ep088a-ampphase-[1,2][a,p].ps   Ef-* baseline amp/phs vs. time

The pair of targets VV705A,B were correlated in multi-phase-center mode,
leading to two stand-alone output sets of FITS files (i.e., each with all
the phase-reference source and fringe-finders scans).  The phase-reference
pairs for the other targets were correleated "normally", and resulted in 
a separate set of FITS files (also including the fringes finders).
There is a separate set of time-based standard plots (weight, amppphase)
for the "normal" [1] and multi-phase-center [2] parts; the latter requires
only one set because the visibility data from the reference source and
fringe-finder is identical in each of the VV705A & VV705B FITS files.
There are also two sets of frequency-based plots (auto, cross), but with
a different distinction between them:  [1] shows 1 minute of data from 
scan 2 (3C345, in all 3 sets of FITS files) and [2] shows all of sccan 255 
(J0152+2207).

The antenna numbering in these plots is 0-based -- thus one less than the
corresponding antenna numbers in the AIPS FITS file.


(a) WEIGHT plots

  The plots shows the weights for all IFs/pols per station, with each
1s integration plotted as a separate ".".   The IF/pol color-coding is:

 IF1/RR = red    IF1/LL = blue      IF2/RR = cyan        IF2/LL = green
 IF3/RR = pink   IF3/LL = med.grey  IF4/RR = brown       IF4/LL = purple
 IF5/RR = teal   IF5/LL = yellow    IF6/RR = steel blue  IF6/LL = lt.grey
 IF7/RR = black  IF7/LL = orange    IF8/RR = lt.green    IF8/LL = lt.purple


(b) AUTOCORRELATION SPECTRA plots

  The plots show data from the scans listed above.  The IFs for each station
are separted by the vertical dashed lines.  Since each station self-scales,
y-axes may not go down to zero.  The polarization color-coding is 
RR=red, LL=blue. 


(c) BASELINE SPECTRA plots 

  The baseline vs. frequency plots show vector-averaged amplitude and phase 
for all baselines for same the time ranges as the autocorrelation plots, with
with amp & phase going to separate plots denoted by the 'a' or 'p' following
the scan identifier, using the same baseline lay-out on the page.
IFs per baseline are separated by the dashed vertical lines.
The polarization color-coding is RR=red, LL=blue, RL=cyan, LR=green. 
Phase(freq) plots show only parallel-hands for clarity.


(d) AMP/PHASE(t) plots 

  The baseline vs. time plots show amplitude and phase for non-target scans,
with amp & phase going to separate plots, denoted by the 'a' or 'p' following
'ampphase-'.  Each 1s integration is plotted as a separate ".", with the
middle 80% of the band used for vector-averaging over frequency.  The plots
use the same IF/pol color-coding as in the weight plots.  The amp(t) plot
for the non-VV705 FITS file (ep088a-ampphase-1a.ps) shows only phase-reference
source scans, because including 3C345 would dominate the y-axis scale (not
as noticeable in the VV705 FITS file, so it was left in for that amp(t) plot).