The 'standard plots' for EZ024 are as follows:

  ez024-weight.ps                station weight vs. time 
  ez024-auto-[1,2].ps            station autocorrelation vs. freq
  ez024-cross-[1,2][a,p].ps      baseline amp/phs vs. freq
  ez024-ampphase-[a,p][1-3].ps   Ef-* baseline amp/phs vs. time

There were 2 different output multiple phase-center targets, but the
standard plots show visibility data from only the reference source and
fringe-finder, so only one set of standard plots is needed.
The auto and cross plots show data taken from scan 1 ([1]) and 64 ([2]),
both 4C39.25.  

The antenna numbering in these plots is 0-based -- thus one less than the
corresponding antenna numbers in the AIPS FITS file.


(a) WEIGHT plots

  The plots shows the weights for all IFs/pols per station, with each
2s integration plotted as a separate ".".   The IF/pol color-coding is:

 IF1/RR = red    IF1/LL = blue      IF2/RR = cyan        IF2/LL = green
 IF3/RR = pink   IF3/LL = med.grey  IF4/RR = brown       IF4/LL = purple
 IF5/RR = teal   IF5/LL = yellow    IF6/RR = steel blue  IF6/LL = lt.grey
 IF7/RR = black  IF7/LL = orange    IF8/RR = lt.green    IF8/LL = lt.purple


(b) AUTOCORRELATION SPECTRA plots

  The plots show data from the scans listed above.  The IFs for each station
are separted by the vertical dashed lines.  Since each station self-scales,
y-axes may not go down to zero.  The polarization color-coding is 
RR=red, LL=blue. 


(c) BASELINE SPECTRA plots 

  The baseline vs. frequency plots show vector-averaged amplitude and phase 
for all baselines for same the time ranges as the autocorrelation plots, with
with amp & phase going to separate plots denoted by the 'a' or 'p' following
the scan identifier, using the same baseline lay-out on the page.
IFs per baseline are separated by the dashed vertical lines.
The polarization color-coding is RR=red, LL=blue.

(d) AMP/PHASE(t) plots 

  The baseline vs. time plots show amplitude and phase for non-target scans,
with amp & phase going to separate plots, denoted by the 'a' or 'p' following
'ampphase-'.  Each 2s integration is plotted as a separate ".", with the
middle 80% of the band used for vector-averaging over frequency.  The plots
use the same IF/pol color-coding as in the weight plots.  The main amp(t) plot
shows omits 4C39.25 to avoid it's dominating the y-axis scale.  The main
phs(t) plot is split into two non-overlapping sub-sets of subbands/pols,
to avoid known dead channels masking the pattern of phase vs. time:
   ampphase-p1 = USB only (for Ur);  RCP only (for Mh, no Noto shown)
   ampphase-p2 = USB only (for Ur);  LCP only (for Nt, no Metsahovi shown)
There is an addition pair of amp/phs plots (ampphase-[a,p]3) showing only
the 4C39.25 scans, for all subbands/polarizations, with integration number
rather than time plotted along the x-axis (to expunge the gap between them).

  The color-coding for the main amp(t) plot and the 4C39.25-only plots is
the same as for the weight plots.  For the two main phase(t) plots, the
color coding is:
     IF2 = red    IF4 = blue      IF6 = cyan        IF8 = green
where, again, each plot shows only the upper-sideband subbands, and each
of the two plots shows only one polarization.